TIM_DeInit(TIM3);//復位TIM3定時器
TIM_TimeBaseStructure.TIM_Period =7999; //設置自動重裝載寄存器鎖存值，1ms溢出
TIM_TimeBaseStructure.TIM_Prescaler = 8;//9分頻
TIM_TimeBaseStructure.TIM_ClockDivision = 0x0; //時鐘分頻因子
TIM_TimeBaseStructure.TIM_CounterMode = TIM_CounterMode_Up;//計數器向上計數模式

TIM_TimeBaseInit(TIM3,&TIM_TimeBaseStructure);//寫TIM3各寄存器參數

TIM_ClearFlag(TIM3,TIM_FLAG_Update);

TIM_ITConfig(TIM3,TIM_IT_Update,ENABLE);

}

文件：usart.h

#ifndef _USART_H
#define _USART_H

#include
#include "stm32f10x.h"

void RCC_Configuration(void); //聲明RCC初始化函數
void GPIO_Configuration(void); //聲明GPIO初始化函數
void NVIC_Configuration(void); //聲明NVIC初始化函數
void USART_Configuration(void); //聲明串口初始化函數
void Time_Init(void); //聲明定時器初始化函數
unsigned short CRC16(unsigned char* puchMsg, unsigned short usDataLen);

#endif

文件：stm32f103x_it.c

//需要設置串口接收中斷和定時器3中斷，中斷時間為1ms

//------------------------------------------------------------------
//函數名：void USART1_IRQHandler(void)
//輸入?yún)?shù)：null
//返回參數：null
//說明：串口接收中斷服務
//------------------------------------------------------------------
void USART1_IRQHandler(void)
{

if(USART_GetITStatus(USART1, USART_IT_RXNE) != RESET) //判斷讀寄存器是否非空
{
// GPIO_SetBits(GPIOB,GPIO_Pin_6);
rx_data[RbufCounter++]=USART_ReceiveData(USART1); //接收字節到接收緩沖區
if(USART_Rsv_Status==0)
{
if(RbufCounter>1)
{
if(rx_data[0]==0xA5&&rx_data[1]==0x5A) //當接收到的數據幀頭兩個字節同時為0xA5和0x5A時
{
USART_Rsv_Status=1;
// USART_SendData(USART1, rx_data[0]);
}
else
{
rx_data[0]=rx_data[1];
RbufCounter=1;

}
}
}
else
{
USART_1ms_Cnt=0;
}
}
}
//------------------------------------------------------------------
//函數名：void TIM2_IRQHandler(void)
//輸入?yún)?shù)：null
//返回參數：null
//說明：定時器2中斷服務
//------------------------------------------------------------------
void TIM2_IRQHandler(void)
{

}
//------------------------------------------------------------------
//函數名：void TIM3_IRQHandler(void)
//輸入?yún)?shù)：null
//返回參數：null
//說明：定時器3中斷服務
//------------------------------------------------------------------
void TIM3_IRQHandler(void)
{

if(TIM_GetITStatus(TIM3,TIM_IT_Update)!=RESET) //判斷是否為定時器3溢出中斷
{

GPIO_SetBits(GPIOB,GPIO_Pin_6);
TIM_ClearITPendingBit(TIM3, TIM_IT_Update);//清中斷標記

if(USART_Rsv_Status==1)
USART_1ms_Cnt++;
if(USART_1ms_Cnt>5)
{
// USART_SendData(USART1,0xAA);
USART_Rsv_Status=0;//連續計數超過5次對USART_Rsv_Status置0，繼續等待接收
USART_1ms_Cnt=0; //當USART_1ms_Cnt>5時對USART_1ms_Cnt重新清零
if(RbufCounter==(u16)rx_data[4]+7) //檢驗數據的完整性
{
int i; //定義循環變量
int j;
data_length=rx_data[4];
for(i=0;i
{
data[i]=rx_data[i];
}
CRC_data_Hi=rx_data[RbufCounter-1];
CRC_data_Lo=rx_data[RbufCounter-2];
CRC_data=CRC16((unsigned char*)data,data_length+5);
CRC_data_Hi1=CRC_data>>8;
CRC_data_Lo1=CRC_data&0x00ff;
if(CRC_data_Hi==(u8)CRC_data_Hi1 && CRC_data_Lo==CRC_data_Lo1)
{
for(j=0;rx_data[j]!=;j++) //循環逐字輸出，到結束字
{
USART_SendData(USART1, rx_data[j]); //發送字符
while(USART_GetFlagStatus(USART1, USART_FLAG_TXE) == RESET)
{
} //等待字符發送完畢
}
}
}
RbufCounter=0;
}
}
}