發送程序如下：

//****************************************************************************// @Module        Project Settings// @Filename      MAIN.C// @Project       20W.dav//----------------------------------------------------------------------------// @Controller    Infineon XC866-2FR//// @Compiler      Keil//// @Codegenerator 2.0//// @Description   This file contains the Project initialization function.////----------------------------------------------------------------------------// @Date          2010-11-4 15:54:56////****************************************************************************// USER CODE BEGIN (MAIN_General,1)// USER CODE END//****************************************************************************// @Project Includes// 完整代碼下載地址:點這里// 與本程序?qū)募t外接收程序代碼:http://www.51hei.com/mcu/1096.html//****************************************************************************#include "MAIN.H"http:// USER CODE BEGIN (MAIN_General,2)#include#define uint  unsigned int   //宏定義#define uchar unsigned char#define  HWTx  P3_0     //位聲明：紅外發射管腳 bit  HWTx_Out;      //紅外發射管腳的狀態bit  Key_Flag,Flag;     //分別是：按鍵按下的標志位，定時器開始的標志位uint Count,Set_Count;    //控制定時時間的變量uchar Table_Tx[4]={0x40,0,0,0};//待發送的緩沖區uchar HWTx_Code,HWTx_data;// USER CODE END//****************************************************************************// @Macros//****************************************************************************// USER CODE BEGIN (MAIN_General,3)// USER CODE END//****************************************************************************// @Defines//****************************************************************************// USER CODE BEGIN (MAIN_General,4)// USER CODE END//****************************************************************************// @Typedefs//****************************************************************************// USER CODE BEGIN (MAIN_General,5)// USER CODE END//****************************************************************************// @Imported Global Variables//****************************************************************************// USER CODE BEGIN (MAIN_General,6)// USER CODE END//****************************************************************************// @Global Variables//****************************************************************************// USER CODE BEGIN (MAIN_General,7)// USER CODE END//****************************************************************************// @External Prototypes//****************************************************************************// USER CODE BEGIN (MAIN_General,8)// USER CODE END//****************************************************************************// @Prototypes Of Local Functions//****************************************************************************// USER CODE BEGIN (MAIN_General,9)// USER CODE END//****************************************************************************// @Function      void MAIN_vInit(void) ////----------------------------------------------------------------------------// @Description   This function initializes the microcontroller. It is //                assumed that the SFRs are in their reset state.////----------------------------------------------------------------------------// @Returnvalue   None////----------------------------------------------------------------------------// @Parameters    None////----------------------------------------------------------------------------// @Date          2010-11-4////****************************************************************************// USER CODE BEGIN (MAIN_Init,1)// USER CODE ENDvoid MAIN_vInit(void){// USER CODE BEGIN (MAIN_Init,2)// USER CODE END///  -----------------------------------------------------------------------///  Configuration of the System Clock:///  -----------------------------------------------------------------------///  - On Chip Osc is Selected///  - PLL Mode, NDIV = 2///  - input frequency is 10 MHz///  *********************************************************************************///  Note : All peripheral related IO configurations are done in the ///  respective peripheral modules (alternate functions selection)///  *********************************************************************************///  Initialization of module GPIOIO_vInit();//   Interrupt PriorityIP            =  0x00;         // load Interrupt Priority RegisterIPH           =  0x00;         // load Interrupt Priority High RegisterIP1           =  0x00;         // load Interrupt Priority 1 RegisterIPH1          =  0x00;         // load Interrupt Priority 1 High Register// USER CODE BEGIN (MAIN_Init,3)// USER CODE END//   globally enable interruptsEA            =  1;           } //  End of function MAIN_vInit
				
            

				
					
					
				
			
                
			
							

                
			            

                            	              		              		上一頁
              		1
              		              			              		              	              				              				2
              					              						              						              				下一頁