Freescale MC9S12XHY256汽車控制解決方案

作者：時間：2012-03-27 來源：網絡

英飛凌汽車電子生態圈
- 掃碼關注
  獲取最新最全汽車電子
  技術方案與實用技巧

Freescale 公司的MC9S12XHY系列是16位微控制器,具有高性能的32位特性, CPU12XV1 CPU內核具有高達40MHz總線頻率,支持CAN和LIN/J2602通信,并提供多達4個步進馬達控制以及40x4 LCD驅動器,帶ECC特性的多達245KB片上閃存和8KB數據閃存,12KB片上SRAM等功能.目標用在低端儀表盤,汽車HVAC步進馬達以及汽車音頻系統.本文介紹了MC9S12XHY256主要特性,方框圖,以及DEMO9S12XHY256演示板主要特性和電路圖.

本文引用地址：http://cafeforensic.com/article/197055.htm

The MC9S12XHY family is an optimized, automotive, 16-bit microcontroller product line focused on low-cost and high-performance. This family is intended to bridge from low-end 16-bit microcontrollers, such as MC9S12HY family, to high performance 32-bit solutions. The MC9S12XHY family is targeted at the lower end of automotive instrument cluster applications, it includes support for CAN and LIN/J2602 communication and delivers typical cluster requirements such as stepper motor control with stepper stall detection (SSD) and LCD Driver.

The MC9S12XHY family delivers all the advantages and efficiencies of a 16-bit MCU while retaining the low cost, power consumption, EMC, and code-size efficiency advantages currently enjoyed by users of Freescale’s existing 8-bit and 16-bit MCU families. Like the MC9S12HY family, the MC9S12XHY family will run 16-bit wide accesses without wait states for all peripherals and memories. The MC9S12XHY family will be available in 100-pin LQFP and 112-pin LQFP package options and aims to maximize pin compatibility with the MC9S12HY family in the 100 LQFP. In addition to the I/O ports available in each module, further I/O ports are available with interrupt capability allowing wake-up from stop or wait modes.

MC9S12XHY256主要特性:

CPU12XV1 CPU core, with up to 40Mhz bus frequency

Up to 256 Kbyte on-chip flash with ECC and 8Kbyte data flash with ECC.

Up to 12Kbyte on-chip SRAM

Up to 40x4 LCD driver

Stepper Motor Controller with up to drivers for up to 4 motors, plus four Stepper Stall Detector modules (one for each motor)

Phase locked loop (IPLL) frequency multiplier with internal filter, supporting 4–16 MHz amplitude controlled Pierce oscillator

Pulse width modulation (PWM) module and Two timer modules (TIM0 and TIM1)

Up to 12-channel, 10-bit resolution successive approximation analog-to-digital converter (ATD)

serial peripheral interface (SPI) module and Inter-IC bus interface (IIC) module

Two serial communication interface (SCI) module supporting LIN communications
Two multi-scalable controller area network (MSCAN) module (supporting CAN protocol 2.0A/B)

On-chip voltage regulator (VREG) for regulation of input supply and all internal voltages

Autonomous periodic interrupt (API) and up to 25 key wakup inputs

MC9S12XHY256目標應用:

Low end instrument cluster

Automotive HVAC stepper motor based actuator control

Automotive Audio system

圖1. MC9S12XHY系列方框圖

DEMO9S12XHY256演示板

The DEMO9S12XHY256 is a demonstration board for the MC9S12XHY256 microcontroller. Application development is quick and easy with the integrated USB-BDM, sample software tools, and examples. An optional BDM_PORT port is also provided to allow use of a BDM_PORT cable. A 40-pin connector provides access to most IO signals on the target MCU.

DEMO9S12XHY256演示板主要特性:

On-Board 4x40 Custom LCD Glass

2 ea. High-Speed CAN Physical Layer Transceivers

Enhanced LIN Physical Layer Transceiver

RS-232 Serial Data Physical Layer Transceiver

Integrated USB-BDM. BDM_PORT header for external BDM cable support

MCU_PORT pin header for access to MCU IO signals

On-board +5V regulator

Optional Power from USB-BDM or MCU_PORT connector

Power Input Selection Jumpers, select from USB-BDM, on-board regulator, Connector J1. Optional Power output through Connector J1

User Components Provided, including 5 Push Switches, 6 LED Indicators, 5K ohm POT w /LP Filter

User Option Jumpers to disconnect Peripherals